|
MemPROG
|
 |
Universal geheugen programmer
Short description:
De Meprog ondersteunt meer dan
13133 chips met software versie:
404 Not Found
Not Found
The requested URL /get_pg4uw_info_full.php was not found on this server.
Additionally, a 404 Not Found
error was encountered while trying to use an ErrorDocument to handle the request.
- small, fast and powerful programmer of EPROM, EEPROM, Flash EPROM, NVRAM
and serial EEPROM
- DIL40 ZIF socket, memories in DIL package up to 40 pins are supported
without adapters
- connection to PC - parallel (printer) port
- high-speed IEEE 1284 printer-port interface, up to 1MB/sec. transfer
rate
- comfortable and easy to use control program, Windows 95/98/Me/NT/2000/XP/Vista/
Windows 7
compatible
- free SW update, download from Internet
- power supply, cable and software included
- approved by CE laboratory to meet
CE
requirements
Available accessories:
Features
GENERAL
- MEMprog is de opvolger van de Preprom-02ALV, deze werkt onder Windows 95/98/ME/NT/2000/XP
Vista met de door Elnec bijgeleverde software. Deze software is simpel en handig
in gebruik, de meeste starter hebben niet meer dan een half uur nodig om het
gehele software programma te door gronden. De MemProg is speciaal gemaakt
voor het snel programmeren vna geheugen chips..
- MEMprog supports virtually all memory types - EPROM, EEPROM,
NVRAM, Flash EPROM and serial EEPROM - including low voltage types. MEMprog
isn't only a programmer, but also a static RAM tester.
- Provides very competitive price with excellent hardware design
for reliable programming. Offer outstanding "value for money" in this
class.
- Very fast programming due to high-speed FPGA driven hardware and
support of IEEE1284 (ECP/EPP) high-speed parallel port.
- MEMprog interfaces with the IBM PC, 486 and above, portable or desktop
personal computers through any parallel (printer) port; it can also
utilize all ECP/EPP advantages.
HARDWARE
- 40 powerful TTL pindrivers provide H/L/pull_up/pull_down and read
capability for each pin of socket. Advanced pindrivers incorporate
high-quality high-speed circuitry to deliver signals without overshoot
or ground bounce for all supported devices. Pin drivers operate down to 1.8V
so you'll be ready to program the full range of today's advanced low-voltage
devices.
- The programmer performs device insertion test (wrong device
position in socket) and contact check (poor contact pin-to-socket)
before it programs each device. These capabilities, supported by
signature-byte check help prevent chip damage due to operator error.
- MEMprog programmer performs programming verification at the
marginal level of supply voltage, which, obviously, improves programming
yield, and guarantees long data retention.
- Various socket converters are available to handle device in PLCC,
SOIC and other packages.
SOFTWARE
- Programmer is driven by an easy-to-use control program with
pull-down menus, hot keys and on-line help. Selection of device is performed
by its class, by manufacturer or simply by typing a fragment of vendor name
and/or part number.
- Standard device-related commands (read, blank check, program,
verify, erase) are enhanced by some test functions (insertion test,
signature-byte check), and some special functions (autoincrement).
- All known data formats are supported. Automatic file format detection
and conversion during loading of file.
- The rich-featured autoincrement function enables one to assign
individual serial numbers to each programmed device - or simply increments a
serial number, or the function enables one to read serial numbers or any
programmed device identification signatures from a file.
- The software also provide a many information about programmed device. As
a special, the drawing of all available packages are provided. The
software provide also explanation of chip labelling (the meaning of
prefixes and suffixes at the chips) for each supported chip.
CARE FOR THE CUSTOMERS
- Support of most new memory devices requires only a software update
due to the MEMprog hardware. With our prompt service you can have a new
device added to the list of supported devices within hours! See
AlgOR (Algorithm On Request)
service for details.
- Free software updates are available by
download from our WEB
site.
- Keep-Current and AlgOR services, our next step towards customer
satisfaction.
- Keep-Current
service means, that ELNEC ships the latest version of programmer
software and updated user documentation (Keep-Current package) to
customer . The Keep-Current service is your hassle-free guarantee that
you are achieving the highest quality programming on ELNEC programmers,
at minimal cost.
- AlgOR (Algorithm On
Request) service gives the user a tool to influence amount and types of
programmed devices as needed.
Specification
HARDWARE
Programmer
- two D/A converters for VCCP and VPP, controllable rise and fall time
- VCCP range 0..7V/350mA
- VPP range 0..25V/200mA
- FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate
- autocalibration
- selftest capability
ZIF socket, pindriver
- 40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil
devices up to 40-pins
- pindriver: 40 TTL pindrivers, specialized GND/VCC/VPP pindriver
- FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all
pindriver pins, level H selectable from 1.8 V up to 5V
- continuity test: each pin is tested before every programming operation
DEVICE SUPPORT
Programmer
- EPROM: NMOS/CMOS, 2708(*3), 27xxx and 27Cxxx series, with 8/16 bit data
width, full support of LV series (*1*2)
- EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data
width, full support of LV series (*1*2)
- Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx
series, with 8/16 bit data width, full support of LV series (*1*2)
- Serial E(E)PROM: AT17Cxxx, 24Cxxx, 24Fxxx, 25Cxxx, 59Cxxx, 85xxx,
93Cxxx, NVM3060, MDA206x, full support of LV series(*1)
- Configuration PROM: 17xxx series, LV series including (*1)
- NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD
U63x series
Notes:
- (*1) - suitable adapters are available for non-DIL packages
- (*2) - there exist only a few adapters for devices with more than 40
pins. Therefore, please, consider a more powerful programmer (LabProg+,
BeeProg, JetProg), if you need to program memories with more than 40 pins
- (*3) - obsolete chips, programming with
additional module
- for all supported devices see
actual DEVICE LIST
I.C. Tester
- Static RAM: 6116 .. 624000
Programming speed
Note: The programming times of the programmer, attached to PC through LPT
port, depends a bit on PC speed, LPT port type and operating system free
resources. Look at ELNEC
programmers, tips to increase of programming speed application note for
details.
| Device |
Operation |
Time |
| 27C010 |
programming and verify |
23 sec. |
| AT29C040A |
programming and verify |
31 sec. |
| AM29F040 |
programming and verify |
60 sec. |
Conditions: P4, 2.4 GHz, ECP, Windows XP.
SOFTWAREAlgorithms: only manufacturer approved or certified algorithms
are used.
Algorithm updates: software updates are available approx. every 2
weeks, free of charge.
Main features: revision history, session logging, on-line help, device
and algorithm information.
Device operations
- standard:
- intelligent device selection by device type, manufacturer or typed
fragment of part name
- blank check, read, verify
- program
- erase
- configuration and security bit program
- illegal bit test
- checksum
- security
- insertion test
- contact check
- ID byte check
- special
- auto device serial number increment
- statistic
- count-down mode
Buffer operations
- view/edit, find/replace
- fill, copy, move, byte swap, word/dword split
- checksum (byte, word)
- print
File load/save
- no download time because programmer is PC controlled
- automatic file type identification
Supported file formats
- unformatted (raw) binary
- HEX: Intel, Intel EXT, Motorola S-record, MOS, Exormax, Tektronix,
ASCII-SPACE-HEX
GENERAL
PC system requirements
- Common, software
related requirements
- Programmer hardware related requirements:
- one (parallel) printer port with nothing attached, the IEEE 1284
compatible printer port (ECP/EPP) on PCI bus recommended
Operation
- operating voltage 12..15V DC, max. 0.5A
- power consumption max. 6W active, about 0.5W sleep
- dimensions 137x65x40 mm (5.4x2.6x1.6 inch)
- weight (without external power adapter) ca. 200g (7.06 oz)
- temperature 5°C ÷ 40°C (41°F ÷ 104°F)
- humidity 20%..80%, non condensing
Base configuration package includes
- MEMprog programmer
- wall plug adapter, 12V/500mA, unstabilized
- connection cable PC-programmer
- diagnostic POD for selftest of the programmer
- anti-dust cover for ZIF socket
- user manual
- software
- registration card
- transport case
Additional services
- Keep Current - ELNEC
sends to user the latest version of programmer software and updated user
documentation (Keep-Current package)
- AlgOR (Algorithms On
Request) - add new supported devices on customer request
Programmer price also includes
- free technical support (hot line)
- free life-time software update via Internet
The information in this document is subject to change
without notice.
|
Bestel Nr: |
Programmer |
Prijs Excl BTW Euro |
| 60-0037 |
MEMprog |
207.00 |
E-Mail
voor vragen aan D.D.S.
requirements
